0

Shopping Cart

Your shopping cart is empty!

Off-Road Tyre Size Chart: How to Read Sizes and Match Them to Your Machine

Aditya Kumar Sahu
Assistant Manager Business Development
7 mins
30 Oct 2026

Summary: About blog: Explains how to read the numbers and letters on an off road tyre, from size and rim diameter to ply rating, tread code and speed symbol. Includes a size chart by machine type and a short checklist for ordering the right tyre.

Off-Road Tyre Size Chart: How to Read Sizes and Match Them to Your Machine

A tyre sidewall is full of numbers, and most of them matter. Ordering from incomplete or incorrect markings can result in a tyre that does not fit the rim, is unsuitable for the required load or wears prematurely. Whether you search for off road tyres or off road tires, the sizing system is the same, and it is easy to read once you know what each part means.

This guide shows how to read the markings, where each machine type fits on an off road tyre size chart, and how to choose the right tyre for your work.

1. How to Read an Off Road Tyre Size

Most off road tyre sizes are written in inches. Take 23.5-25 as an example:

  • 23.5 is the section width in inches.
  • 25 is the rim diameter in inches.
  • The dash between them means a cross-ply (bias) construction.

When the dash is replaced by an R, as in 16.00R25, the tyre is radial. Radial tyres usually run cooler and last longer on long hauls, while cross-ply tyres have strong sidewalls that suit rough, low-speed work.

Larger tyres may use a metric size, such as 750/65R25. Here 750 is the width in millimetres, 65 is the height as a percentage of the width, and 25 is the rim diameter in inches.

2. Other Markings on the Sidewall

MarkingExampleWhat it tells you
Ply rating (PR)20PRStrength and load capacity of a cross-ply tyre
Load index and speed symbol191A2, 180BMaximum load the tyre can carry and the speed it is rated for
Tread codeL3, E3, E4The pattern and the work it is built for
Tube type or tubelessTT or TLWhether the tyre needs a tube and flap

Ply rating is an older strength rating, and today it describes strength rather than the actual number of plies. Ply rating indicates a tyre’s load-carrying capability at the specified inflation pressure; it does not represent the actual number of plies. Many tyres also display a load index and speed symbol. Radial tyres usually show a load index instead.

3. Understanding Tread Codes

The letter identifies the tyre’s service category, while the number identifies its tread or application classification within that category.

CodeMachinePattern
E3Earthmover, truckRock pattern, normal depth
E4Earthmover, truckRock pattern, deep tread
L2LoaderTraction pattern
L3LoaderRock pattern, normal depth
L5LoaderRock pattern, extra deep tread
G2, G3GraderTraction and rock patterns

Within the same service category, codes such as 3, 4 and 5 generally indicate progressively deeper tread classifications. The appropriate code still depends on the machine, operating conditions, speed and load. Deeper treads last longer in rock, but they cost more and can run hotter.

4. Off Road Tyre Size Chart by Machine

The table below groups the tyre sizes available in the Tuffex range by their listed machine application. It uses the sizes in the Tuffex range.

MachineSizes and specifications in the Tuffex range
Backhoe loader9.00-16 16PR; 16.9-28 12PR
Wheel loader17.5-25 20PR L3; 23.5-25 20PR L3; 14.00-25 20PR E3
Motor grader13.00-24 16PR; 14.00-24 16PR or 20PR
Mining tipper10.00-20 18PR; 11.00-20 18PR; 12.00-20 20PR; 12.00-24 20PR
Mining tipper (radial)12.00R24 24PR, 161B
Wide body truck16.00-25 40PR; 16.00R25 E3 or E4, 180B

These are application groupings from the Tuffex range, not universal fitment recommendations. Confirm the machine model, rim specification, load requirement and approved tyre size before ordering.

5. Best Tyres for Wheel Loader Work

Wheel loaders put heavy, repeated loads on the tyres, along with sharp turns and constant contact with rock. The best tyres for wheel loader work usually share these features:

  • An L3 pattern for general quarry and construction work, with deeper L5 for harsh rock.
  • A size that matches the rim, such as 17.5-25 or 23.5-25.
  • The right construction: tubeless for convenience, tube-type where rims or sites call for it.
  • A load and speed rating suited to short, slow cycles.

Tuffex lists 23.5-25 20PR L3 tyres in both tube-type and tubeless versions. The tubeless one comes with an O-ring, and the tube-type with a tube and flap.

6. Choosing the Best Off Road Tyres for Your Site

The best off road tyres are not the most expensive ones. They are the ones that match your machine, ground and duty cycle. Ask three questions:

  • What is the ground like: soft, rocky, abrasive or mixed?
  • How much weight does the machine carry, and how far does it travel?
  • Do you need traction, cut resistance or long wear?

For soft or mixed ground, a traction pattern gives better grip. For rock and quarry work, a rock pattern with a deeper tread resists cuts and wear. On long hauls, radial tyres often run cooler and give better life.

If one site has both soft and rocky ground, pick the pattern that suits the ground where the machine spends most of its hours. Then review it after the first set wears, using the wear pattern as your guide.

7. Tube-Type or Tubeless?

A tube-type tyre uses an inner tube and may also require a flap, depending on the tyre and rim configuration. A tubeless tyre seals directly against a compatible rim and may use an O-ring on certain multi-piece OTR rims. Do not change between tube-type and tubeless configurations without confirming tyre and rim compatibility.

8. Common Tyre Ordering Mistakes

MistakeWhat happensHow to avoid it
Matching width but not rim diameterTyre will not fit the rimCheck both numbers, such as 23.5-25
Mixing radial and cross-ply on one axleUneven handling and wearFit the same construction on an axle
Choosing a deep rock tread for soft groundPoor grip and extra heatMatch the pattern to the ground
Ignoring ply rating or load indexOverload and early failureFollow the machine and tyre manufacturer’s approved load, speed and inflation specifications

Most of these come from reading only part of the size. Take a photo of the full sidewall before you order, and keep it with the machine record for next time.

9. Before You Order: A Short Checklist

  • Read the full size from the old tyre.
  • Note the ply rating or load index, and the tread code.
  • Check whether it is tube-type or tubeless.
  • Confirm the machine make, model and rim.
  • Choose a tread pattern for your ground.
  • Ask the supplier to confirm fit.

The Tuffex off-road tyre range covers 18 tyres across sizes and patterns from Apollo Tyres and Effiplus Tires, with a 3-year warranty. The Tuffex off-road tyre range contains 18 tyres from Apollo Tyres and Effiplus Tires, with a three-year warranty listed for each product. The listings provide the tyre size and relevant specifications, such as construction, ply rating, load and speed marking, tread code and included accessories, where applicable.

Frequently Asked Questions

What does 23.5-25 mean on a tyre?
The tyre is 23.5 inches wide and fits a 25 inch rim. The dash shows a cross-ply construction.
What is the difference between a dash and an R in tyre size?
A dash means cross-ply (bias) construction. An R means radial.
What does L3 mean on a loader tyre?
L stands for loader, and 3 is a rock pattern with normal tread depth.
Can I fit a different size from the one on my machine?
Only with the OEM's approval. Changing size affects speed, load and handling.
Are off road tyres the same for all machines?
No. Loaders, graders, backhoes and tippers use different sizes, patterns and strengths.
Tuffex gradient
Menu
Get Recommendations
Sign in to unlock your experience